Welcome to the official website of Chengdu Senge environment protection technology Co., Ltd


Chengdu senge environmental protection technology co.LTD

Consultation Hotline:02865357899

Production, Sales and Development of Ion Exchange Resin



Product Categories

Hot key words

Contact us

Contact person: Manager Liu

Location: 028-65357899

Mobile phone: 15680686111

Mailbox: chengdu@sgrhb.com

Fax: 028-65357899

Email: chinaresin@sgrhb.com

Website: www.sgrhb.com

Website  :    en.sgrhb.com

Address: 79 Jiujin Street, Wuhou District, Chengdu City, Sichuan Province

Prevention and Control of Ion Exchange Resin Pollution

Your current location: Home >> News >> Ion exchange resin knowledge

Prevention and Control of Ion Exchange Resin Pollution

Date of release:2019-04-08 Author: Click:

  Prevention and Control of Ion Exchange Resin Pollution

  1. Controlling chlorine content

  We should do a good job in disinfection and algae killing of pretreatment and control the residual chlorine before entering the cation exchanger.

  2. Regular scrubbing

  The resin is washed regularly with compressed air to remove suspended solids, organic matter and iron.

  3. Selection of Coagulant

  In order to do a good job in coagulation and clarification, coagulant must be selected correctly, and the best dosage of Zui must be determined by experiments, so as to prevent the backward movement of aluminium salt and iron salt, strictly control the turbidity of the effluent of sand filter and activated carbon filter, Al3+, Fe3+ should be less than 0.3 mol/L, and COD of chemical oxygen demand should be less than 1 mol/L. Organic substances are adsorbed by activated carbon filtration.

  4. Preventing Oil Pollution

  For the compressed air that may be in contact with resin, it is necessary to purify and degrease to prevent oil mist from being brought into it, and to prevent oil pollution near the water source suction outlet.

  5. Preventing contamination of regenerants

  In order to prevent the impurities in the regenerant from polluting the resin, in addition to selecting high-quality regenerant, anti-corrosion measures should be taken for the containers during the transportation and storage of the regenerant to prevent rust and organic coating from falling off and polluting.

  Pollution and Recovery of Anion Exchange Resin

  Sichuan anion exchange resin is often polluted by organic matter, colloidal silicon and iron compounds in use.

  The method of resin resuscitation contaminated by organic substances usually adopts salt-sodium hydroxide cleaning method, i.e. using 10% NaCl and 1% - 2% NaOH mixed liquor three times as much as the bed to clean the resin, and then thoroughly backwash it. When the effect of this method is not good, sodium hypochlorite can be used for cleaning. The prepared cleaning solution should produce 1% active chlorine.

  The colour of ion exchange resin becomes black after it is polluted by iron. The resuscitation method can be soaked in 4% sodium sulfite solution for 4-12 hours. Sodium hyposulfite is a reductant that cleans high-valent iron precipitates into soluble, low-valent forms from resins. The acid pickling method can also be used, that is, the anion resin is treated with brine after failure, and then immersed in 10% hydrochloric acid for 5-12 hours.

  In addition, in recent years, special agents for cleaning polluted ion exchange resins and new technologies for ultrasonic cleaning have emerged.

  Pollution and Recovery of Anodic Resin

  Sichuan cation exchange resin will be polluted by suspended matter, iron, aluminium, oil, CaSO4 and other substances in the influent water. The following different treatment methods can be used for the types of pollutants in operation:

  (1) Air scrubbing method

  Using compressed air, Sichuan ion exchange resin was scrubbed and backwashed repeatedly until the backwash water was clarified.

  (2) pickling method

  For iron, aluminium, calcium and magnesium salts, 3%~10% hydrochloric acid can be used for immersion or low flow rate cyclic acid pickling.

  (3) Non-ionic surfactant cleaning method

  For resins contaminated by organic substances such as lipids and proteins, the resin can be converted to sodium type at first, and then non-ionic surfactants such as octylphenol and polyoxyethylene ether can be added to the backwashing water for backwashing, and the pollutants can be removed by backwashing.

The address of this article:http://en.sgrhb.com/news/466.html

Key word:IonExchangeResin,Ionexchangeresinpollution

Recently browse:

Chengdu Senger Environmental Technology Co., Ltd.

Record No: 蜀ICP备19000327号

Powered by Xiangyun Platform 

Contact person: Manager Liu

Location: 028-65357899

Mobile phone: 15680686111

Email: chinaresin@sgrhb.com


  • Service
  • number
  • Message
  • Online Service