Welcome to the official website of Chengdu Senge environment protection technology Co., Ltd


成都森格尔环保科技有限公司

Chengdu senge environmental protection technology co.LTD


Consultation Hotline:02865357899

Production, Sales and Development of Ion Exchange Resin

成功案例

News

Product Categories

Hot key words

Contact us

Contact person: Manager Liu

Location: 028-65357899

Mobile phone: 15680686111

Mailbox: chengdu@sgrhb.com

Fax: 028-65357899

Email: chinaresin@sgrhb.com

Website: www.sgrhb.com

Website  :    en.sgrhb.com

Address: 79 Jiujin Street, Wuhou District, Chengdu City, Sichuan Province


Pollution and Recovery of Anion Exchange Resin in Sichuan Province

Your current location: Home >> News >> Anionic Resin Knowledge

Pollution and Recovery of Anion Exchange Resin in Sichuan Province

Date of release:2018-12-17 Author: Click:

  Chengdu Senger Environmental Technology Co., Ltd. shares pollution and recovery methods of anion exchange resin:

  Anion exchange resins are often contaminated by organic compounds, colloidal silicon and iron compounds in use.

  Resuscitation of resin contaminated by organic substances usually uses salt-sodium hydroxide cleaning method, i.e. using 10% NaCl and 1% - 2% NaOH mixed liquor three times as much as the bed to clean the exchange resin, and then thoroughly backwash. When the effect of this method is not good, sodium hypochlorite can be used for cleaning. The prepared cleaning solution should produce 1% active chlorine.

  The colour of ion exchange resin becomes black after it is polluted by iron. The resuscitation method can be soaked in 4% sodium sulfite solution for 4-12 hours. Sodium hyposulfite is a reductant that cleans high-valent iron precipitates into soluble, low-valent forms from resins. The acid pickling method can also be used, that is, the Sichuan anion exchange resin is treated with brine after failure, and then immersed in 10% hydrochloric acid for 5-12 hours.

  In addition, in recent years, special agents for cleaning polluted ion exchange resins and new technologies for ultrasonic cleaning have emerged.

  Prevention and Control of Ion Exchange Resin Pollution

  1. Controlling chlorine content

  We should do a good job in disinfection and algae killing of pretreatment and control the residual chlorine before entering the cation exchanger.

阴离子交换树脂


  2. Regular scrubbing

  The resin is washed regularly with compressed air to remove suspended solids, organic matter and iron.

  3. Selection of Coagulant

  In order to do a good job in coagulation and clarification, coagulant must be selected correctly, and the best dosage of Zui must be determined by experiments, so as to prevent the backward movement of aluminium salt and iron salt, strictly control the turbidity of the effluent of sand filter and activated carbon filter, Al3+, Fe3+ should be less than 0.3 mol/L, and COD of chemical oxygen demand should be less than 1 mol/L. Organic substances are adsorbed by activated carbon filtration.

  4. Preventing Oil Pollution

  For the compressed air that may be in contact with resin, it is necessary to purify and degrease to prevent oil mist from being brought into it, and to prevent oil pollution near the water source suction outlet.

  5. Preventing contamination of regenerants

  In order to prevent the impurities in the regenerant from polluting the resin, in addition to selecting high-quality regenerant, anti-corrosion measures should be taken for the containers during the transportation and storage of the regenerant to prevent rust and organic coating from falling off and polluting.


The address of this article:http://en.sgrhb.com/news/465.html

Key word:anionexchangeresin

Recently browse:

Chengdu Senger Environmental Technology Co., Ltd.

Record No: 蜀ICP备19000327号

Powered by Xiangyun Platform 

Contact person: Manager Liu

Location: 028-65357899

Mobile phone: 15680686111

Email: chinaresin@sgrhb.com



四川离子交换树脂1544145157754088.png

  • Service
  • number
    15680686111
  • Message
  • Online Service